No marker found inside MarkerDistance 792 Distance coded RMS axis _. If the HDS machine gets a 'skew error': Check the display on the motor amplifier (machine would have to be run with the control console door open). Input signal label->i2OCA/ 3)Error of cooling unit for M-Spindle head oil cooling. HDS Machine Freezes during Tool change, or when it tries to do a tool change in a g-code file.
Also, check the wires inside the control box. It was not X directional advanced end limit position at the time of support equipment short selection or steady rest selection. Release E-stop, and click E-stop release on screen. 001 EMERGENCY STOP ACTIVE and042 AXIS ON OVERTRAVEL LIMIT Machine suddenly stopped in the middle of a cut and displayed 2 error messages. Fix the part program (error 828) or try a different sequence of operations durin...Page 52MACHINEMATE® Software Manual – Error Messages page 52/59 2. http://www.cncalarms.com/
Exchange of a mixing valve. 22->Exchange of detection PS of oil-air increase. The actual Spindle/Sub-Spindle speed is above a Specified Limit; when Synchronized Peripherals at Waiting Position code is off. 33->MA/MB Revolution Command is issued; when Synchronized Peripherals at Waiting Position code is Use the correct Techno post in the CAM package and output the file again. Try a...Page 36MACHINEMATE® Software Manual – Error Messages page 36/59 master programmed axis.
Or in phase synchronization, second spindle was not lower position. [Related functions] MACTURN series + sub-spindle 1814 W-axis movement condition W-axis movement was designated when the condition was not satisfied. [Code] Exit safe zone, reset controller, and restart program. 090 Zone B intrusion sensor tripped The safety interlock has been triggered during the cut cycle. Only one block with controlled running out allowed! Fanuc Error Codes Pdf Inferiority of a lubrication of spindle by oil-air pump. 24->Inferiority of detection PS of oil-air increase.
Home | Sitemap | 中文 Our Products Product Features Resource Center About Us Contact UsGrinder User's Manual CNC Error Message Search Catelog Download Contact Us CNC Error Biesse Rover Error Codes Check the compensation value ...Page 13MACHINEMATE® Software Manual – Error Messages page 13/59 117 Spline not finished 118 Wrong start point The above errors involve a spline programming problem. G-code file has an incorrect arc Arcs must be absolute i’s and j’s, or created using R. http://www.generalcnc.ca/user_forum/?msgbrd=3&topic=49 Check tool touch off probe to make sure it is functioning correctly and not sticking.
This alarm occurs when the following two input signals are kept ON or OFF for 0.5 second or longer. Fanuc 18i Alarm List Once the machine is powered down, push the x axis a little bit, towards the middle of the machine. Check and fix the active part...Page 18MACHINEMATE® Software Manual – Error Messages page 18/59 211 Axis limit __ The above error involves an axis programming problem. This alarm occurs when the following two input signals are kept ON or OFF for 0.5 second or longer.
The current values for all variables will be shown to the operator, perhaps enabling the cause of the error message to be determined. http://support.technocnc.com/HDS-error.htm Check that PSI to machine is sufficient. Cnc Error Codes Upon reaching the software travel limit the CNC will prevent further motion in that direction. Scm Cnc Error Codes There is an unrecognized command in the g-code file.
Typically, the error comes from the circle radius being smaller than the D value. It was not X directional retracted position at the time of support equipment long selection. 3->It was the following conditions at the time of steady rest original point return/retract position movement Therefore, electromagnetic lock switch should be faulty or its wiring is disconnected. [Measures to Take] Check the electromagnetic lock switch and its wiring on the safety fence. 1873 Door interlock The Check and fix...Page 23MACHINEMATE® Software Manual – Error Messages page 23/59 326 SERCOS: Service channel: ident __ drive _. Biesse Error Codes
Make sure that all of the connectors are secure on them. Synchronized Peripherals at Waiting Position Code is off; during Traverse. 35->Turret Index Command is issued; when Synchronized Peripherals at Waiting Position code is off. Or a work rest was not down position when the spindle was moving. 2->An up to middle position work rest move command was issued with the tailstock sleeve not at the The above errors are SERCOS problems with the service channel.
The above errors come from the CNC trying to access a PCI interrupt from a PCI card. Fanuc Robot Error Codes The touch off probe can be dirty, therefore, proving inaccurate tool offset. Fanuc CNC alarms list with error codes and descriptions Yaskawa/Yasnac CNC controls alarms and error codes Mitsubishi alarms list and error codes CNC machine builder alarms and more.....
No more trying to dig through the Equipment manuals only to find generic error information. Many of these errors involve NC part programming errors. SEARCH 100 - PARAMETER WRITE ENABLE 101 - PLEASE CLEAR MEMORY 109 - P/S ALARM 110 - DATA OVERFLOW 111 - CALCULATED DATA OVERFLOW 112 - DIVIDED BY ZERO 113 - Fanuc Alarm List Pdf In addition, the machine controller should be properly grounded so that system interruption or failure does not occur due to poor ground. (See Fig. 1.) HDS Touch Off Location - HDS
With the machine on "continuous" mode click "save origin". Low incoming air pressure. Your cache administrator is webmaster. NOTE: This error has nothing to do with the computer.
Check to see that the dust shroud sensor is lit red when the dust shroud is in the up position.