The default is 5, therefore a request for the sixth volume will fail with a E37 S80A S804 S822 S80A, S804 Region too small for the program to run S822 - What is error code for end of record/record not found in DB2? This indicates that a journal referenced in the file definition is using an MVS logstream, which in turn, is using a coupling facility structure which has been defined with a MAXBUFSIZE The journal in error can be the forward recovery log or the journal used for auto-archiving. check my blog
AAO4 DFHZARL, or a module called by DFHZARL, has detected a logic error. Either the command (or an application stub) has become corrupted, or the unavailable function needs to be generated (CICS command), ENABLEd (non-CICS command), or exceptionally the non-CICS support has suffered damage Reading a file that is not open Your SORTIN DCB was not correct Mixing compile options RES and NORES in different modules S0C4 An uncontrolled loop moved data on top of For example, the modules called and their parameters. https://www.ibm.com/support/knowledgecenter/SSAL2T_8.2.0/com.ibm.cics.tx.doc/reference/r_tx_error_codes.html
At ADP, this generally happens on test CICS after a checkin/LI function. ABMX A text string passed to BMS contained a set attribute order that was invalid for one of the following reasons: 1. There are situations where file should be read if exists, write if it does not when you dont know whether file exists are not , first you will open file in
load module Other abend codes and their possible reasons The usual Response codes can also be seen in a compile listing for any CICS-COBOL code ABMO - An ABMO error means This error is almost certainly caused by the module receiving invalid data or indicators from VTAM. User Response: Use the transaction dump to determine why the start has failed. Cics Error Handling AED8 A terminal control error has occurred in DFHEDFX.
In plain words it means CICS has not identified the terminal the transaction is run on. Jcl Error Code There are two possible causes of this error. 1. AEXF ESCERROR condition not handled. https://www.tutorialspoint.com/cics/cics_status_codes.htm AEI0 PGMIDERR condition not handled.
The domain that detected the original error will have provided an exception trace, a console message, and possibly a system dump (depending on the options in the dump table). Aeyh Cics Error This indicates either a logical loop or that the system is overloaded, ultimately it will bring the whole CICS down. User Response: Check your library setup to ensure that all of the VS COBOL II interface modules are present. User Response: Redefine and install a new definition either for the transaction with TASKDATAKEY(USER), or for the program with EXECKEY(CICS).
AEZB A transaction has been defined with a TASKDATALOC(ANY), and the application is attempting to call a task related user exit. click AFCV A request made against a file opened in RLS mode was unable to acquire a record lock. Db2 Error Code Index exceeds the size of table 2. Cobol Error Code AICA Program in infinite loop, A task has been executing for longer than the runaway time interval (defined by the ICVR operand on the system initialization table macro, DFHSIT)
ABMD DFHTPR or DFHTPP has issued a DFHDI TYPE=SEND and has received a return code other than "FUNCERR-REQUEST FOR CHANGE DIRECTION SIGNALED" or "NORESP" ABME DFHTPR click site It was purged either by the master terminal operator or as a result of deadlock timeout. User Response: A level 2 trace for 'CP' of the transaction shows the course of events prior to this error, for example, the modules called and their parameters. DFHRLR is attempting to scan the TCT for a BMS ROUTE request with LIST=ALL or operator class or operator ID specified in the route list. Vsam Error Code
A RETURN command with the Commarea option is issued in a program that is not at the highest logical level. ABML The terminal control locate routine received invalid data from DFHRLR and returns with an error return code. If a program is looping then you may not get an AICA abend, because the timer can be reset when certain events occur, e.g. news Analysis: Because these abend codes are directly related to exceptional conditions that can be specified in HANDLE CONDITION commands, the application programmer should decide whether the condition is one that should
A level 2 trace for 'CP' of the transaction shows the course of events prior to this error, for example, the modules called and their parameters. Asra Cics Error o Following a READ UPDATE command for a data set, a WRITE or READ UPDATE command is issued for the same data set before exclusive control is released. If it has, check that it has been speelled correctly.
TEMPORARY STORAGE CONTROL: o Occurs if the length of the stored data is greater than the value specified by the length option for move-mode input operations. AETS An error (EXCEPTION, DISASTER, INVALID, KERNERROR, or PURGED) has occurred on an INQUIRE_STARTUP call to recovery manager (RM) domain. This indicates that the EXEC CICS command has become corrupted. Cics Abend Codes Try to iinsert duplicate record. -805 -> DBRM or PACKAGE not found in PLAAN -811 -> Cursor should be used , when morre than one row returned as an result of
AEIZ ITEMERR condition not handled. Usually this error occurs because the picture is S9(8) instead of S9(4) or is not COMP. AEXY The executing transaction has been purged before control could be returned. More about the author An E37 on tape datasets is most often caused when the number of requested volumes is exceeded.
AEXI TERMERR condition not handled. AETL An error (EXCEPTION, DISASTER, INVALID, KERNERROR or PURGED) has occurred on an SET_UOW call to the recovery manager (RM) domain. AEX7 NETNAMEIDERR condition not handled. S0C1 - Operation Exception.
The ICVR parameter in the CICS SIT table can be used to specify a value for all tasks running in CICS, or you can specify a RUNAWAY value when a transaction REASON SQLCODE -804, Error: AN ERROR WAS FOUND IN THE APPLICATION PROGRAM INPUT PARAMETERS FOR THE SQL STATEMENT, REASON SQLCODE -803, Error: AN INSERTED OR UPDATED VALUE IS INVALID AICN An incorrect response has been returned from a user RAMESH KRISHNA REDDY ABEND CODES / STATUS CODES JCL | DB2 | CICS | VSAM | IMS ABEND CODE IO error, damaged tape, device malfunction.
AICL DFHEIIC detected an invalid function code in the command level parameter list. The data set or Vsam is not open. APCT means that mapset name in the COBOL program does not match the mapset name in front of the DFHMSD assembler macro. AEDG CICS has suspended the user task to allow the EDF task to complete.