In the event of major changes in the contents of this manual over a long or short period. Solution: Press Start button after confirming the first DIS from the other party during a manual call. Cause: Cannot transmit signals properly due to poor line conditions. Remedy2 Delete documents stored in the Mail Box and Fax/I-Fax Inbox. weblink
Cause: Malfunction due to CRF echo. The following paragraph does not apply to any countries where such provisions are inconsistent with local law. Resend the fax after a while. FAX settings Check 7: Is the fax number registered correctly for memory dialing? http://www.worldoffax.com/G3%20Service%20Codes.htm
For details, see Summary of Reports and Lists. Solution: Refer to Service Manual. ##305 [ TX ] System error between modem and MCPU. When making an overseas call, add a pause to the fax number.
Page 175 Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. Page 54 Chapter1: User Error Codes #301 [ TX/RX ] Subscriber number of the other party has changed Cause Remedy • The called number is no longer in use. • Check T.62 T3 Timer: It is a CSA timer used as part of a channel B communication procedure. Canon Fax Error Code 0091 Solution: Boost the transmission level so that the other party can receive the signals immediately before GC2, PIS or the Phase signals.
Solution: Power cycle the machine (unplug unit). Canon Fax Error Codes Ng A. Solution: Boost the transmission level so the other party can receive EOM or PIS signal properly. Solution: Adjust the NL equalizer to receive picture signals properly. ************** ##670 [TX] At V.8 late start, the called party declares the V.8 protocol in DIS signal and this
Procedure Signal: It is a generic term for a tonal signal and a binary signal. Canon Printer Error Codes Cause: The transmitter disconnected the line during phase 2 or the signal from the transmitter was not able to be detected. Solution: No solution as modem speed is dependant on each machines specifications. The system returned: (22) Invalid argument The remote host or network may be down.
A. look at this site A. Canon G3 Fax Error Codes search Search the Wayback Machine Featured texts All Texts latest This Just In Smithsonian Libraries FEDLINK (US) Genealogy Lincoln Collection Additional Collections eBooks & Texts Top American Libraries Canadian Libraries Universal Canon Fax Machine Error Codes A.
Solution: Have the other party boost the transmission level to receive picture signals properly. have a peek at these guys Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##114 [ RX ] RTN was transmitted during reception. Solution: Lengthen the no-sound time after receiving CFR so the other party can receive picture signals properly. ##284 [ TX ] DCN reception after TCF transmission. mode to find out the cause. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. #049 [ TX ] Canon Fax Error Codes 018
If a description is underlined and marked with an asterisk with a number, you will find explanations on the next page. Provides a description of the possible cause of the error code in question. 6. Cause: The ink detection sensor is faulty Solution: Replace the ink detection sensor Solution: Replace the unit containing the ink detection sensor. ##349 [ TX ] Home position check over here CNG, CED, and ANSam are tonal signals.
Solution: Adjust the NL equalizer so the other party can receive picture or EOP signals properly. Canon Copier Error Codes Cause: The other party cannot receive the signals properly due to low transmission level. line do not match. #102 [ TX/RX ] Subaddress or password does not match during an ITU-T-compliant subaddress communication Cause...
Solution: Lower the transmission level to prevent the reception of echo signals. ##107 [ RX ] Fall back failure on TX side during reception. All documents and all page layouts were created with Adobe PageMaker 6.5®. Page 59 Chapter1: User Error Codes Cause Remedy Cause Remedy 1-46... Canon Camera Error Codes Cause: The read end sensor stays ON or OFF.
Remedy Re-enter the group destination, and try sending again. Page 113 Chapter 2: Service Error Codes ##300 [ TX ] Interface error occurred between the reader and the controller Cause Remedy • An internal unit is faulty (i.e., after the Page 82 Chapter 2: Service Error Codes ##120 [ TX ] Mechanism of the document feed system is faulty Cause Remedy • A fault occurred in a mechanism of the • this content A.
A. The password is not printed to maintain security. Preamble: It is a signal attached to the beginning of a binary signal, and is used to synchronize modem signals for a procedure signal. Page 41 Chapter1: User Error Codes #055 [ TX ] The other party does not have an MDC (Multi Device Controller) function [exclusively for GP55] Cause Remedy • Although an attempt
This manual covers all localities where the facsimiles are sold. Modes of Transmission Normal Transmission: A normal transmission is one that does not specify the confidential, broadcast, or subaddress function. Cause: The other party's line was released. Cause: SCNT PWB trouble.
A. Solution: Press the START button after confirming the first DIS from the other party during a manual call. If necessary, ask the operator of the other party to transmit once again. #054 [TX/RX] Call cannot be made [Korean model] Cause Remedy • The user ID has not been registered. Solution: Relax the RTN transmission conditions to prevent RTN transmission.
A. Page 218 Chapter 2: Service Error Codes ##1070 [ TX/RX ] Only restricted digital information bearer capability is available Cause Remedy • Cause number #70 (Only restricted digital • Start a Solution: Replace the SCNT PWB. ##348 [ TX / RX ] Ink detection sensor error. Remedy1 Check the scan settings, and try scanning again.
ask the operator to set normal polling trans- mission, and use polling reception. • If the other party is a Canon machine, use polling reception in Canon mode polling. #083 [ A. If you unplugged the power cord after pressing the ON button to turn off the power (the POWER lamp is off), reconnect it, then press the ON button to turn on Cause 3 Transmission via fax driver is not allowed.