Solution: Boost the transmission level so that the other party can receive NSC properly. The user called the correct number, but the machine was configured not to answer. Quick Memory Transmission: In this mode, the other party is dialed while an document is being read into memory. Disable ECM. weblink
Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##002 [ RX ] Picture memory full upon G2 reception. A. Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the Confirm that the remote user has the correct password, and that the local machine is configured with the same password, if this option is available. 230 The remote machine attempted to
Solution: Adjust the NL equalizer so the other party can receive the signals immediately before GC2, PIS or the Phase signals. A. Solution: Lower the transmission start speed to 4800 bps. Cause: Abnormal protocol.
Cause: SCNT PWB malfunction. Cause: The BJ controller in the BJ printer control unit is faulty. Use the tables in this document to view fax error codes and solutions. Canon Fax Machine Error Codes Solution: Press Start button after confirming the first DIS from the other party during a manual call.
However, the remote diagnostic versions that are supported by the two machines are incompatible. Canon Laser Class 7000 Check Printer 330 If everyone would just READ the thread before posting, 99\% of the questions would be answered immediately. error went away. More Bonuses Cause: Defective internal unit.
Solution: Replace SCNT PWB Solution: Replace the modem or modem attached circuit board. Panasonic Fax Machine Error Codes There might be no solution because the remote machine could be defective. 381 ECM The remote machine failed to respond to a fax command from the local machine because the connection Cause: The user telephone number is not registered; (if receiver is Ricoh 3000L). Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##102 [ TX ] Fall back failure during transmission.
Cause: Other party confused by echo and does not send G12. forward cancel coming check printer... Canon Laser Class 7000 Error Code 330 A. Canon Fax Error Ng B.
A. http://ebprovider.com/error-code/cannon-fax-error-codes.php Is there a way for you to program it to print out a confirmation page when you send a fax. PAPER. . . . Cause: Too much power applied to the Thermal head. Canon Fax Error Code 018
Not finding what you are looking for? Solution: Lower the transmission level so the echo of the CFR transmission is not received. ##104 [ TX ] RTN or PIN received during transmission. Solution: Record the protocol on DAT tapes and then request the Local Canon office and/or Technical Center to analyze the information. ##013 [ TX ] Receive PIS during picture signal check over here These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line).
The time now is 05:06 AM. Brother Fax Machine Error Codes A. Solution: Adjust the NL equalizer to receive the phase signal properly. ##607 [ TX ] Fail CFR reception during MF1 transmission.
Solution: Replace the DECODE control unit (PRINT, etc.). ##238 [ RX ] PRINT control unit malfunction. Solution: Boost the transmission level so that the other party can receive carrier signals properly. Any Ideas on what is wrong with it? Canon Error Codes Cause: The UPI to control the display did not function properly Solution: Replace the display control unit (display unit, etc.). ##231 [ TX / RX ] Button control unit
The manual has no reference to it and I didn't see it marked on the outside of the machine. Replaced the cap and the error went away....But so did any printing ability.I can't get it to copy or print any kind of report.What now?Appreciate any info.... Solution: Contact the telephone company and request line maintenance. ##010 [ RX ] Failed Phase synchronization on first sheet during reception in G2 or MF1. this content Can anyone tell me how to program or what page this programing is on?
Cause: Abnormal protocol; (fill or EOL present in picture data). Solution: Perform echo measures as outlined in Service Manual. Ask the remote machine user to send at a lower resolution setting. Cause: Defective internal unit.
A. Other reasons can include power brownouts and other power-related problems. Solution: Have the other party add an EPT to the V29 modem signal. ##737 [ RX ] Picture decode error during ARQ reception. Ask the community!
Make sure the remote machine can accept and use polling. The TO timer is used to set the period of time in which a line connection is recognized for transmission, i.e., in which the machine waits for a significant signal from A. by unknown on Jul 7, 2005 at 2:42pm Add comment Please sign in to comment 0 My Canon 7000 fax has the words "Data Error" on the little screen.
Thank you. Any help would be great. Solution: Boost the transmission level so that the other party can receive the phase signal properly. Support Forum Join the conversation!
by Keith on May 1, 2004 at 7:46pm Add comment Please sign in to comment Thanks...Filling up the tray solved my problem. Solution: Turn off the power and unplug the unit. No.03 is used to set the burst error (number of successive error lines identified as an errors); (2 to 99 lines). Solution: Power off and unplug the unit and wait awhile for machine to cool down.
This includes postage within the USA. Solution: Refer to Service Manual. ##302 [ TX ] Interface error between reader and controller.