I promptly installed it and fired the washer back up. Submitted: 6 years ago. An inspection of the rest of the wiring harness in the cabinet revealed several areas were water and corrosion from the cabinet had dripped down onto the harness. If you need more help, let us know. http://ebprovider.com/error-code/calypso-washer-error-code-fl.php
Top Load Washer - White See Details Kenmore 28133 5.3 cu. Press STOP/CANCEL to clear the display. I'm now employed by a commercial cooking equipment service company Related Appliance Questions Question Date Submitted I have a LG front load washer that i replaced the the three 10/5/2016 The small green square=personal message. http://www.shopyourway.com/questions/1091538
The green dot is a link to my web page on appliance repair and other general BS I love to post. ft. Same bat channel!
Press START to continue the cycle from the moment that power was lost –OR- Press STOP/CANCEL to clear the display and completely cancel the cycle. ft. Thanks, Jim. Kenmore Elite Calypso Washer Error Code Ob Top-Load Washer w/ ...
Meanwhile, an another new motor is on order. Calypso Washer Error Codes Ld Press STOP/CANCEL to clear the display. it says on here All Stages Open to Answer so here is what it says for the error code you have "CA" "Cl" Average current limit Or Instantaneous current limit If http://www.shopyourway.com/questions/1125207 The alarm sounded several times, briefly and weakly, when the wiring harness was shaken near the junction.
is online now Kenmore Calypso washer wont start and Im getting the C1 Customer Question Kenmore Calypso washer won't start and I'm getting the C1 code. Calypso Washing Machine Error Codes Overloading or excessive suds can also cause this error. and other Appliance Specialists are ready to help you Ask your own question now Expert: Appliance Tech Larry replied6 years ago. See Details More Products Kenmore 23102 3.6 cu.
Current overloading. http://www.justanswer.com/appliance/340kx-whirlpool-calypso-washer-getting-c1-error.html You can use the diagnostic test procedure shown in the second image to check the washer and see if the C1 code still appears. Whirlpool Calypso C1 Error Code Average current trip occurs if there is a 2 second average of current draw greater than 5.55 Amps at the motor windings. Kenmore Calypso Washer Error Codes this is what the book says Average Current Limit or Instantaneous Current Limit If a status signal comes back from the motor controller that a current limit has been breached, the
This question will give you some good detailed suggestions, while your waiting on an expert answer. check over here It's good to know you're out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air. Subscribe ApplianceAssistant on Youtube! Search Site For Parts Call (877) 338-6774 Like ApplianceAssistant on Facebook! The Calypso was the first Whirlpool washer with nutation motion for the wash system. Kenmore Elite Calypso Washer Error Code Ld
It was no big deal at first since the error was infrequent and I could set the washer to spin the load then place it in the dryer. If ... I liked that I could ask additional questions and get answered in a very short turn around. his comment is here Before I IM-ed the Samurai I preformed the Motor and Motor Control System Test (Test #3 pages 8 and 9 of the Tech Sheet).
Freshfield, Liverpool, UK This expert is wonderful. Kenmore Elite Calypso Washer Error Codes That is why it is difficult to test the current draw at the motor windings .... If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle.
Compact Electric ... Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent. Couldn't have asked for more. Whirlpool Cabrio Cl Code The first image below shows the procedure for opening the console of the washer.
If you’re thinking of joining I found the site well worth the $50 tuition. Sometimes the basket is damaged removing it. If the problem is consistent I'd suggest a technician check and repair the problem or you check out the brand new similar Energy Star You should also measure between 2 and 5 ohms between the yellow and white/black wires. weblink ft.
Can I override? Report This by Manage My Life September 15th, 2010 Share it! If a winding is bad in the motor then it will need to be replaced. NOTE: You should only attempt to diagnose and repair this problem yourself if you are completely confident Back To Top PM Quote Reply Posted: Sat Dec 17th, 2005 02:30 am PM Quote Reply 14th Post Pegi Fellow, Academy of Sublime Masters of Appliantology Joined:Tue May 3rd, Opening the lid will allow the customer to view and redistribute the load.
Their minions are everywhere. Both the CI and CA error codes refer to the dive motor. I have forgotten which button though. Question about Whirlpool Washing Machines 1 Answer Calypso GVW9959K Top Load Washer: when washing a C1 code appears... ...C1 error is displayed when the motor tries to pull more than 26
Meanwhile, should anyone else have this problem I’ve found a way to keep the machine in service until its fixed. Also, the stand pipe the washer drains into is only 36” high not the recommended minimum height of 39”. Press STOP/CANCEL to clear the display. there is no C1 on a Calypso washer ,, only Cl Ask Your Own Appliance Question Share this conversation JustAnswer in the News: Ask-a-doc Web sites: If you've got a
The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Justanswer.com. i am getting a c1 error code under any wash setting including rinse and spin. Overloading or excessive suds can also cause this error.
Thank you so much!!!! Back To Top PM Quote Reply Posted: Mon Nov 14th, 2005 09:31 pm PM Quote Reply 12th Post AppGuy Master Appliantologist Joined:Fri Nov 11th, 2005 Location: Posts:280 Flavorite