Thread Tools Rating: Display Modes #1 05-08-2009, 06:49 PM rbmclaughlin Registered User rbmclaughlin's PC Specs Join Date: May 2009 Posts: 5 POST ID # = 400671 Reputation: 10 Attribute: Erase Fail Count (chip)". more WD Green drives, the only long-term solution is probably to just call all the drives a loss and replace them with something else. That is why it is a 'pending sector'.The above analysis seems to be in line with the analysis on this page:http://smartmontools.sourceforge.net/ba ... 2_example1Quote:Should the drive find the sector is instead absolutely http://ebprovider.com/crc-error/crc-error-smart-utility.php
software for Linux, Michael Cornwell. This is my third HD that says "Interface CRC Error" (WRITE DMA EXT) using Smart Utility 3.1.1. I know crc errors are basically connection interface errors. JEDIDIAH Ars Praefectus Registered: Aug 14, 2007Posts: 4663 Posted: Mon Feb 03, 2014 7:14 pm RobL777 wrote:Quote:I've always used reallocated sector counts to determine the usable life of the drive. pop over to these guys
Archived from the original (PDF) on 2013-05-07. Upgrade Upgrade to Bigger and Better. Just keep a good backup.
Often these are represented as "drive OK" or "drive fail" respectively. I'm also not talking about the normalized value on the page with the thresholds. For some reason, this seemed to correct the problem; I don't get any more CRC errors when copying data in either direction. Interface Crc Error Count 200 but feel it does or the parts/assembly push the acceptable tolerances.
But I did do a clean install on it to begin with. Udma Crc Error Count Smart Current starts at 200 and will count down the way as sectors get reallocated. As you said, it seems like I definitely would have seen problems by now if the reports weren't bogus. http://www.tomshardware.com/answers/id-2697812/hdtune-interface-crc-error-count.html exposed to the host) is unreadable, the relocation of this sector with a reserve sector is 'pending' a resolution; either the sector has to be read successfully or it has to
Customer Service and Technical Support Center I Think I Have a Bad Part. Interface Crc Error Count Attention I'll keep it as brief as I can while mentioning potentially relevant stuff: I recently installed a 2nd internal hard drive (purchased new) into my Unibody MBP 15", using MCE's Optibay Attribute ID Threshold Value Worst Raw TypeÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ* Raw Read Error Rate 1 6 I don't really want to reinstall OS X, but I will if 10 CRC errors is something to be concerned about.
The error count is NOT increasing as time goes on. http://www.hdsentinel.com/forum/viewtopic.php?f=32&t=9482 I have a few external housings that do not. Smart Utility Interface Crc Error Acronis International. Interface Crc Error Count Fix Viewer 2.00 Copyright (C) 2001-2003, Sysinfo Lab Copyright (C) 1997, Michael Radchenko
You can not post a blank message. this page quiethdd. 13 December 2009. Although an industry standard exists among most major hard drive manufacturers, issues remain due to attributes intentionally left undocumented to the public in order to differentiate models between manufacturers. From a Alternatively, if a drive has experienced problems in the past, but the sensors no longer detect such problems, the SMART status may, depending on the manufacturer's programming, suggest that the drive Interface Crc Error Count Ssd
Devin Ars Tribunus Angusticlavius Tribus: Student of Glosophopaphrology Registered: Sep 9, 2001Posts: 8100 Posted: Fri Sep 30, 2011 12:20 am Eh, what? utilities will report a negative number for the raw value since in reality it has 48 bits rather than 32. 243 0xF3 Total LBAs Written Expanded The upper 5 bytes of Scotts Valley, California: Seagate Technology. http://ebprovider.com/crc-error/crc-error-count-smart.php Open Menu Close Menu Apple Shopping Bag Apple Mac iPad iPhone Watch TV Music Support Search apple.com Shopping Bag : CommunitiesContact SupportSign inContentPeopleSearch Support CommunitiesNotebooksMacBook Pro Please enter a title.
If the values that you are seeing with a third party SMART utility are not displaying properly or seem to be false, please contact your software vendor for further explanation of Interface Crc Error Count Reset So, now they've swapped places in their bays, and who knows why it worked, but the problem does seem to have been corrected! I also started with NO errors, and am now up to 12 errors, with the last error being "command aborted".
Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? On the Windows side, however, internal transfer was still very slow, 1/10 or so what it should be. This attribute returns the total number of Flash erase operation failures since the drive was deployed. C7 Interface Crc Error Count Attention That SFF standard described a communication protocol for an ATA host to use and control monitoring and analysis in a hard disk drive, but did not specify any particular metrics or
Retrieved 12 July 2016. ^ Stephens 2006, p.207Of the 512 octets listed in table 42 on page 207: "Device SMART data structure" a total of 489 are marked as "Vendor specific". I don't consider it very useful. Customer Service and Technical Support Center I Think I Have a Bad Part. useful reference Retrieved 12 July 2016. ^ WD VelociRaptor Spec Sheet (PDF), WD ^ WD Green Spec Sheet (PDF), WD ^ "WD VelociRaptor SATA Hard Drives" (PDF).
August 2010. siguardian.com. I searched online, and finally found a little VB Script that someone had written to force Windows' IDE channels into DMA mode (http://winhlp.com/node/10), which, happily enough, seemed to correct the problem; Compaq placed IntelliSafe in the public domain by presenting its specification for the ATA environment, SFF-8035, to the Small Form Factor Committee on May 12, 1995. ^ "ATA/ATAPI Command Set (ATA8-ACS)"
sub.mesa Smack-Fu Master, in training Registered: Jun 1, 2010Posts: 57 Posted: Sat Sep 17, 2011 11:09 am Quote:Threshold is at 140, so when 60 sectors have been reallocated and Current and Ultimately, the disc drive design determines which attributes the manufacturer will choose. FireCuda PC & Gaming – SSHD: Seagate FireCuda: A Ferociously Fast Hard Drive. Tried everything.
I assume you've tried a Disk Utility check? Normally this attribute value should be equal to zero and if the value is far above zero, then most likely there will be some serious problems with power supply or an attributes and the typical meaning of their raw values.